How to Fix Holes in Drywall

How to Fix Holes in Drywall

DIY Drywall How-to

When it comes to home repairs, fixing holes in drywall is a common task that many DIY enthusiasts encounter. Whether it's a small nail hole or a larger puncture, knowing how to properly repair drywall can save you time and money. In this guide, we’ll walk you through the steps to fix various types of holes in drywall, ensuring a smooth and professional finish.

What You'll Need:

  • Drywall patch kit
  • Joint compound (spackle)
  • Putty knife
  • Sanding sponge or sandpaper
  • Drywall tape
  • Utility knife
  • Stud finder (like Walabot)
  • Paint and primer

1. Fixing Small Holes (Nail and Screw Holes)

For small holes left by nails or screws, the repair process is straightforward:

  1. Clean the Area: Use a utility knife to remove any loose drywall or debris around the hole.
  2. Apply Spackle: Using a putty knife, apply a small amount of joint compound (spackle) over the hole. Smooth it out to ensure an even surface.
  3. Sand the Surface: Once the spackle is dry, sand the area smooth to blend it with the surrounding wall.
  4. Prime and Paint: Apply primer over the repaired area, then paint to match the rest of the wall.

2. Repairing Medium-Sized Holes

For holes that are larger than nail holes but smaller than large punctures (like those caused by door handles):

  1. Cut a Patch: Cut a piece of drywall slightly larger than the hole.
  2. Attach the Patch: Use drywall tape to secure the patch over the hole.
  3. Apply Joint Compound: Spread joint compound over the patch and tape, feathering the edges to blend with the wall.
  4. Sand and Finish: Once dry, sand the area until smooth, then prime and paint.

3. Fixing Large Holes

Larger holes require a bit more effort but can still be repaired with basic tools:

  1. Prepare the Hole: Cut the hole into a neat square or rectangle using a utility knife.
  2. Cut a Drywall Patch: Cut a new piece of drywall to fit the hole.
  3. Install Support: Use a stud finder to locate the nearest studs. Attach wooden supports (furring strips) behind the drywall if the hole is between studs.
  4. Attach the Patch: Screw the drywall patch into place, securing it to the studs or supports.
  5. Tape and Mud: Apply drywall tape around the edges of the patch. Spread joint compound over the tape, feathering the edges.
  6. Sand and Paint: After the compound dries, sand the area smooth, then prime and paint.

4. Fixing Drywall Anchor Holes

Drywall anchors can leave unsightly holes when removed. Here’s how to fix them:

  1. Remove the Anchor: Carefully remove the anchor from the wall.
  2. Fill the Hole: Fill the hole with spackle or joint compound.
  3. Sand and Paint: Once dry, sand the area smooth, then prime and paint.

Common Questions:

What is the best thing to fill holes in drywall?

  • Joint compound or spackle is commonly used to fill holes in drywall. For larger holes, a combination of drywall patches and joint compound is best.

How do you fix a punched hole in drywall?

  • Follow the steps for fixing large holes, ensuring to cut a clean patch and secure it properly.

How to fix a screw hole that is too big in drywall?

  • For oversized screw holes, use a drywall patch or fill the hole with joint compound, then reinforce with a drywall anchor if needed.

Tips for a Professional Finish:

  • Always sand between coats of joint compound to ensure a smooth surface.
  • Use a primer before painting to ensure the repaired area blends seamlessly with the rest of the wall.
  • Consider using a stud finder to avoid future mishaps with nails or screws.

By following these steps, you can confidently tackle drywall repairs, from small nail holes to larger punctures, ensuring your walls look as good as new. Remember, having the right tools, like a stud finder from Walabot, can make the job easier and more efficient.

 

 

Back to blog